BCGZW - D.E.N. 438,EPOXY NOVOLAC
- MSDS: BCGZW
- Manufacturer: DOW CHEMICAL USA
- Product Name: D.E.N. 438,EPOXY NOVOLAC
- National Stock Number: 8010-00N001100
Product Identification
Product ID:D.E.N. 438,EPOXY NOVOLAC
MSDS Date:01/01/1985
FSC:8010
NIIN:00N001100
MSDS Number: BCGZW
Responsible Party
Emergency Phone: 517-636-4400
Cage: EO044
Contractor
Telephone: 800-258-2436
Cage: EO044
Ingredients
PHENOL
CAS: 108-95-2
RTECS: SJ3325000
OSHA PEL S, 5 PPM
ACGIH TLV: S, 5 PPM; 8990
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
FORMALDEHYDE (SARA III)
CAS: 50-00-0
RTECS: LP8925000
OSHA PEL SEE 1910.1048
ACGIH TLV: C 0.3 PPM; A2; 9293
EPA Report Quantity: 100 LBS
DOT Report Quantity: 100 LBS
EPICHLOROHYDRIN (SARA III)
CAS: 106-89-8
RTECS: TX4900000
OSHA PEL S, 5 PPM
ACGIH TLV: S, 2 PPM; 9293
EPA Report Quantity: 100 LBS
DOT Report Quantity: 100 LBS
Hazards
Effects of Overexposure:SKIN/EYE IRRITATION.
First Aid
First Aid:EYE CONT:FLUSH WITH WATER 15 MIN,GET MED ATTN.SKIN CONT:WASH
WITH SOAP & WATER,REMOVE CONTAMINATED CLOTH.INDUCE VOMITING IF
LARGE AMOUNTS ARE SWALLOWED,GET MED ATTN.
Fire Fighting
Flash Point:490F/254C (TOC)
Extinguishing Media:FOAM,CO*2,DRY CHEMICAL
Accidental Release
Spill Release Procedures:USE APPROPRIATE SAFETY EQUIP,SOAK UP WITH
ABSORBENT MATERIAL OR SCRAPE UP.RESIDUE CAN BE REMOVED WITH
NON-FLAMMABLE SOLVENTS SUCH AS METHYLENE CHLORIDE.
Handling
Handling and Storage Precautions:PRACTICE GOOD CAUTION AND PERSONAL
CLEANLINESS TO AVOID SKIN/EYE CONTACT.AVOID BREATHING VAPORS OF
HEATED MATERIAL.
Exposure Controls
Respiratory Protection:NIOSH/MSHA APPROVED RESP DEVICE IAW EXPOSURE OF
CONCERN
Ventilation:LOCAL/MECHANICAL
Protective Gloves:RECOMMENDED
Eye Protection:SAFETY GLASSES WITH SIDES
Other Protective Equipment:CLEAN BODY-COVERING CLOTHING.
Supplemental Safety and Health
Chemical Properties
Spec Gravity:1.16
Appearance and Odor:LIGHT YELLOW LIQUID
Percent Volatiles by Volume:1
Stability
Stability Indicator/Materials to Avoid:YES
BASE
Stability Condition to Avoid:EXCESSIVE HEAT DEGRADE THE RESIN,INCREAS
VISCOSITY & EPOX WT
Conditions to Avoid Polymerization:MAY OCCUR WITH ALPHATIC AMINES IN
MASS BREATER THAN 1 POUND
Disposal
Waste Disposal Methods:BURN IN ADEQUATE INCINERATOR OR BURY IN AN
APPROVED LANDFILL LOCAL,STATE & FEDERAL LAWS APPLY.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.